EGW HK VP9 Optics Ready Mounting Plate for Vortex Viper / Venom (fits Burris FastFire and Docter) Adapter Plate for


Out of stock

SKU: 49287 Category: Product ID: 6785


Vortex Viper / Venom (fits Burris FastFire and Docter) Adapter Plate for HK VP9 OR ‘ VP9L Optics Ready Mounting Plate

Mounting hardware is included.

This mount fits:
All HK VP9 Optics Ready Models
HK VP9 Optics Ready
HK VP9L Optics Ready
HK VP9 Tactical Optics Ready

If your gun has a cut out for the optics plate, this plate will work with your application.

(This mount is comparable to the HK VP9 Optics Ready #5 Plate)

The screws that come with your slide to mount the plate to the slide may be reused. They are also available for purchase from the drop down above. HK recommends replacing the plate mounting screws after 2,000 rounds. HK recommends torquing the screws for the plate to 2Nm or 17.7 in/lbs.

The screws to mount the red dot to the plate are provided at no extra cost. We recommend using 15 in/lbs.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.921″
Overall Width: .99″
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws – Requires 5/64 Wrench or Driver
(2) 6-32 Flat Head Screws – Requires 5/64 Wrench or Driver

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Sightmark Core Shot

*All ADE mounts require 6-32 x 3/8″ screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

Simply remove the plate on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Red dot mounting hardware included.

Installation Instructions
– Remove the rear cover plate
– Install the EGW sight mount and torque the mounting plate screws
– Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
– Apply blue Loctite to the provided mounting screws
– Torque red dot mounting screws to 15in/lbs

2 Button Head Cap Screws – Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws – Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64” allen wrench for installation.

Modification of your firearm may nullify the manufacturer’s warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Additional information

Weight 0.25 oz
Dimensions 10.0 × 5.0 × 1.0 in

The Sporting Jack. All rights reserved 2022.

The Sporting Jack. All rights reserved 2022.